By Yuhuan Kang'erda Sanitary Ware Co., Ltd. | 09 August 2022 | 0 Comments
Pull out kitchen faucet instruction and maintenance manuel
Pull out kitchen faucet instruction and maintenance manuel
I, Wamer reminding before you installing the pull out kitchen faucet:
1, Please clean the water supply pipe before installing.
2, Spout can be rotated 360°, handle spout can be pulled down/out for 0.5m meter for convenient use.
3, Water pressure:
Min pressure: 0.05Mpa(flow pressure)/Max Pressure: 0.75Mpa(static pressure)
4, The water temperature can't be exceeding 90°, suggested temperature is 60±5°, steam is not permitted for hot water supply.
II, Installation instruction.
1, Put all hoses into the gasket, deckboard and bottom deckboard in order and insert all hoses and screw rod into the sink installation hoes(picture 1).
2, Place the fixing gaskets into the screw rod as the arrow direction, adjust the faucet position, tighten the nut and place the anti-skidding nut at the end of the screw rod(picture 2).
3. Place the counterweight/weight on the pull out hoses according to the dimension on the drawing, tighten it with the wrench, pull out the sprayer, it can automatic reset to the original position. Connect the pull-out hose with outlet hoses(picture 3).
III, Installation check.
Check and make sure that all connects have been tightened and the handle is closed(turned off).
Open water supply valves and check the leakage. Disassembly the sprayer and open the handle for both hot water and cold water. Keep the water to run for about 60 seconds to clean impurities and check the leakage. Close the faucet handle(turned off). Clean the sprayer to remove impurities and reassembly the sprayer.
IV. Caution and maintenance.
To keep your faucet with long durability, please wipe your faucet softly.
Cleaning with a damp non-abrasive spnge and buffing it dry with a clean soft cloth should keep your faucet looking shinny and beautiful. To remove water spots, use warm water and a soft damp cloth. Hard water stains may be removed by using a 50/50 solution of white vinegar and water, and make certain that you rinse thoroughly with water afterward.
Please keep your main water supply valve closed when you don't use your faucets for a long time.
Avoid using the following which can damage finish:
A, Avoid industrial cleaners and abrasive cleaners, such as those used for toilet bowls, green scotch-brite heavy duty scrub sponges, scrubbing bubbles bathroom cleaner and Lysol basin tub, soft scrub, and tile cleaner.
B, Avoid products that state on the label that they remove tarnish and rust, and those containing hydrofluoric, hydrochloric and /or phosphoric acids and caustic agents.
C, Avoid harsh abrasivers or polishes.
D, Avoid bleach-based cleansers.
I, Wamer reminding before you installing the pull out kitchen faucet:
1, Please clean the water supply pipe before installing.
2, Spout can be rotated 360°, handle spout can be pulled down/out for 0.5m meter for convenient use.
3, Water pressure:
Min pressure: 0.05Mpa(flow pressure)/Max Pressure: 0.75Mpa(static pressure)
4, The water temperature can't be exceeding 90°, suggested temperature is 60±5°, steam is not permitted for hot water supply.
II, Installation instruction.
1, Put all hoses into the gasket, deckboard and bottom deckboard in order and insert all hoses and screw rod into the sink installation hoes(picture 1).
2, Place the fixing gaskets into the screw rod as the arrow direction, adjust the faucet position, tighten the nut and place the anti-skidding nut at the end of the screw rod(picture 2).
3. Place the counterweight/weight on the pull out hoses according to the dimension on the drawing, tighten it with the wrench, pull out the sprayer, it can automatic reset to the original position. Connect the pull-out hose with outlet hoses(picture 3).
III, Installation check.
Check and make sure that all connects have been tightened and the handle is closed(turned off).
Open water supply valves and check the leakage. Disassembly the sprayer and open the handle for both hot water and cold water. Keep the water to run for about 60 seconds to clean impurities and check the leakage. Close the faucet handle(turned off). Clean the sprayer to remove impurities and reassembly the sprayer.
IV. Caution and maintenance.
To keep your faucet with long durability, please wipe your faucet softly.
Cleaning with a damp non-abrasive spnge and buffing it dry with a clean soft cloth should keep your faucet looking shinny and beautiful. To remove water spots, use warm water and a soft damp cloth. Hard water stains may be removed by using a 50/50 solution of white vinegar and water, and make certain that you rinse thoroughly with water afterward.
Please keep your main water supply valve closed when you don't use your faucets for a long time.
Avoid using the following which can damage finish:
A, Avoid industrial cleaners and abrasive cleaners, such as those used for toilet bowls, green scotch-brite heavy duty scrub sponges, scrubbing bubbles bathroom cleaner and Lysol basin tub, soft scrub, and tile cleaner.
B, Avoid products that state on the label that they remove tarnish and rust, and those containing hydrofluoric, hydrochloric and /or phosphoric acids and caustic agents.
C, Avoid harsh abrasivers or polishes.
D, Avoid bleach-based cleansers.
Leave a Reply
Your email address will not be published.Required fields are marked. *